|  | Note: You can use this "combiner" as a decombiner as well. So if you don't want to use a wall plate, you can order TWO combiners instead. |
|  | |
Connect your aerial and LNB into the combiner upstairs, indoors, as close to the TV aerial as possible. Connect the combiner output to the outlet plate downstairs using a single continuous run of double-shielded cable (see page 8). (Ordinary "TV aerial cable" is very unlikely to give satisfactory results so please do not ask). Combines both signals into one cable and separates them at the outlet plate. Note: The units allow the LNB voltage and 22kHz signals to pass to the LNB without reaching the aerial. Some signal loss is inevitable so this system is not recommended for installation where the signal is already borderline in bad weather. In some cases the aerial signal may need additional amplification/attenuation. To combine two satellite LNB signals you need a Stacker/Destacker which we no longer sell. |
| |
|  | V24-310 FM+DAB+UHF triplexer. Combine all your aerial feeds into one cable. This can be fed into the DIP2 (above) to add the LNB feed as well. So all feeds can go down one cable to a decombiner wall plate or to another V24-310 to decombine them. See technical section for wiring diagram suggestion. It can also be used to combine your aerial feeds into a Global amplified splitter. You do not have to use all aerial inputs. Unused inputs should be fitted with a 75 Ohm terminator if interference occurs (usually it won't). |
|  
| Choose delivery method |  | |
|  These are high-quality units made by Fringe. | Set-back amplifiers Please refer to our technical information before ordering. Requires mains power outlet within 1 metre. | |
| | | |
Low Cost Amplified Splitters (SkyLink compatible) |
| Please read our NOTES. |
|  | Labgear CA121-F. This is a 2-way distribution amplifier (8dBgain) which is compatible with the SkyLink "magic eye" remote extender systems (TV Link, DigiLink, SLXlink etc. on page 3), providing a 9 volt supply for all types of "magic eye". Requires threaded "F" connectors on the cable. Use double-shielded cable throughout. It can be powered by the Sky Digibox "RF Outlet 2" (or with any regulated 9 volt DC power supply fitted with a 3.5mm jack plug). Where amplification is not required (short cable runs) you may be able to use our low-cost 2-way passive splitter instead. The CA121-F is a budget version of the F120 below. See Technical notes |
| |
|  | Labgear CA141-F. This is a 4-way distribution amplifier (7dB gain) which is compatible with the SkyLink "magic eye" remote extender systems (TV Link, DigiLink, SLXlink etc. on page 3), providing a 9 volt supply for all types of "magic eye". Requires threaded "F" connectors on the cable. Use double-shielded cable throughout. It can be powered by the Sky Digibox* "RF Outlet 2" or with any regulated 9 volt DC power supply fitted with a 3.5mm jack plug. The CA141-F is a budget version of the F140 below. Right-click HERE to download PDF data sheet for CA121/CA141. See Technical notes * Not all Sky Digiboxes can supply power to more than two "magic eyes". You may need to buy a separate power supply in addition. (Currently we don't offer a PSU for this.) |
| Choose delivery method |  | |
|  | Amplifier Bypass Kit Allows the TV Link or Digilink/SLXlink signals to go around an ordinary amplified splitter. It's better to use a SkyLink compatible amplified splitter (above) but if you've already installed the wrong type of amplifier, the Bypass Kit might be a cheap fix. You can use only one ONE of these per amplifier. See page 3 for Digilink and SLXlink |
|
| Choose delivery method |  | |
|  | Global DA (7dB gain) - T120, T140 and T180 Amplifiers Global 2- and 4-way distribution amplifiers are UHF TV signal distribution amplifiers which are 100% compatible with the SkyLink system, allowing the 9 volt supply to pass through, and with digital TV. Unlike other amplifiers they can tolerate both high and low input levels. Flat gain response between 40MHz and 850MHz allows UHF, DAB and VHF signals to be combined and fed into the amplifier (but a Loft Box is a better way to do this). 2 Way, 4 Way and 8 Way available 2 Way, 4 Way needs a dc inserter/PSU if used without Sky Digibox. (If you use an Amp without a Sky Digibox you must order a separate power supply). 8-way needs a Power Supply (supplied with it) and access to a 230v mains power point. 2 Way and 4 Way can be powered by the Sky Digibox* OR by the tvLINK-Plus system. * Not all Sky Digiboxes can supply power to more than two "magic eyes". You may need to order the separate power supply in addition. This also applies for the Humax Foxsat when used with our modulator kit. NOTE: "F" types require "F" connectors on the coaxial cable (easier to fit). Others require male TV plugs. Make sure the centre TV plug wire is crimped or soldered. Use double-shielded cable (eg. RG6 type). DC socket plug should be 5mm O/D x 2.5mm I/D. If you wish to combine aerial feeds into an amplifier you will need a V24-310 (above). See Technical notes |
| Need more than 8 outputs? See our Amp Adder or the F280 below... |
|  | Global F280 16 way UHF distribution amplifier - Skylink compatible
- 8dB gain with 12 volt power supply
- Typical noise figure 3dB
- Output capability 85dBµV
- 47 - 860MHz bandwidth
See Technical notes |
| | | |
|  | GLO76A Power Supply for Global T120, T140, F120, F140 When you use one of these amplifiers *without* connecting it to a Sky Digibox or tvLINK-Plus system, you will need this power supply unit. 9v/500mA (E.g. when using it for a non-Sky satellite system or a terrestrial aerial system.) Not suitable for Labgear amplifiers that use a 3.5mm jack plug connection. |
| Choose delivery method |  | |
| FREE |  | Free eBook "Piping TV Around the House" when you buy any Loft Box. When you receive your order comfirmation e-mail ("Keep-me" message) it will contain a download link for the eBook. |
| |
|  | Labgear HDU681S Loft Box Labgear TV Distribution System It is a distribution system similar to the one below. More info and purchase. |
| |
|  | Loft Box The Philex unit is obsolete and has been superseded by the Labgear HDU681S. It is a distribution system similar to the one below. More info and purchase. |
| |
|  | Loft Box The Global 'LoftBox' is an integrated INHome Distribution system. It has additional expansion accessories available for purchase which are not available for the Philex unit. Normally located in the Loft, it combines TV, FM, DAB, CCTV & Satellite onto one down cable, feeding to a Global Triplexing wallplate or a MSWP in the living room. (See wall plates below). The 'LoftBox' takes a return feed from the living room which would typically be from the UHF2 output from the Sky digibox. FM & DAB are diplexed onto the return feed & then distributed to additional points within the house via Global TV/FM diplex wallplates. Each outlet point is able to receive normal terrestrial TV, FM, DAB, CCTV & the selected Satellite channel. The 'LoftBox' fully supports the Infrared control signals from the tvLINK Remote Eye back to the Sky digibox. More info and purchase. |
| Need more than 8 outputs? See our Amp Adder |
| |
|  | Televes Attic Box (by popular request) Similar to the Loft Boxes but a completely different system. Click here for more information. |
| |
|  | Triax 333112 DDU 8-way Loft Box with Multiroom connections for Sky+ Digital More info and purchase. |
| |
|  | The Global Loftbox expander has been designed to allow two LNB outputs to be connected to an existing Loftbox distribution system. It is ideally suited for use when a SKY+ receiver is being installed which requires two feeds from the dish but there are no spare cables available to take the extra signal feed. The unit operates by adding the additional dish signal onto the returning UHF cable between the RF2 port and the UHF2 port on the Loftbox. A diplexer WILL be required in the living room in order to successfully extract the second dish signal ready for connecting into the satellite receiver. You MUST use proper satellite cable for all feeds. More info. |
| |
|  | Global DIP1 decombining Diplexer This decombiner is designed to separate a terrestrial UHF aerial signal and a satellite LNB signal from one cable. A Global loft box or Diplexer is used to combine the signals. More info. |
| |
|  | AP01224 DAB/FM decombining Diplexer. Plugs into FM socket on wall plate to separate FM and DAB radio signals from Loft Box. OBSOLETE. Please use V24-310 TRIPLEXER instead. |
| Choose delivery method |  | |
|  | Adding more outlets to a Loft Box or an Amplifier - More Info. Click HERE if you need a power supply. |
| glo27 glo28 gl027 gl028 wall outlets faceplates IMPORTANT: if you need to cut the dish (LNB) cable to fit a wall plate, DISCONNECT the satellite receiver power plug from the mains power socket first! Dont miss our Modular wall plates with clip-in socket inserts Notes: Triplex plates can not have a TV DC connection because that would mix with the SAT DC feed (LNB power). However, it doesn't normally matter because a Loft Box feeds power to the Remote Extender. If you are not using a Loft Box, you will need to find an alternative way to insert the DC power feed if you are using one or more Remote Extenders ("magic eye"). Diplex plates (TV and Radio) pass power only through the TV connection. Diplex plates (TV and SAT) pass power only through the SAT connection. You can drill blanking plates to fit '090-3078 Threaded "F" barrels'. We stock only fully-screened wall plates. What does this mean? The wall plates, below, and the modular wall plates on page 15a, are the only ones we stock. Please don't email us to ask if we are hiding away any other colours or configurations! |
|  | *Non-isolated means that there is no capacitor to prevent a small DC voltage passing through so the socket can be used where a current at up to 24 volts is required to power equipment such as a tvLINK or an aerial masthead amplifier. This plate has one cable feeding TV (UHF) into it. The TV socket can also feed the remote control signals back to a suitable Loft Box or amplifier. This female UHF (TV) output socket requires a male TV (IEC) plug. MORE INFO |
| |
|  | *Non-isolated means that there is no capacitor to prevent a small DC voltage passing through so the socket can be used where a current at up to 24 volts is required to power equipment such as a tvLINK or an aerial masthead amplifier. Off-white. This plate needs two cables. RG6 recommended. MORE INFO. |
| |
|  | 100-00107 "F" connector wall plate for Digital satellite and TV Unlike many wall plates, this has a threaded "F" connector which goes ALL THE WAY THROUGH. You fit an "F" plug on the cable coming through the wall and screw it directly into the rear connector. (Conventional unscreened types use a bridge clamp and a screw which kink the cable AND leave the central core exposed to interference.) A shallow wall box might suffice, provided that the cables come straight through the wall without bends. Otherwise requires a DEEP wall box. (35mm recommended). May require a right-angle F adaptor (see page 7). Suitable for carrying all signals 0 - 2015 MHz. Buy our Digital Wall Plate and insist that your installer fits it! Read about interference wallplate |
| |
|   | PLATE4F wall plate with 4 'F' connectors. Unlike many wall plates, this has four threaded "F" connectors which go ALL THE WAY THROUGH. You fit an "F" plug on the cable coming through the wall and screw it directly into the rear connector. (Conventional unscreened types use a bridge clamp and a screw which kink the cable AND leave the central core exposed to interference.) A shallow wall box might suffice, provided that the cables come straight through the wall without bends. Otherwise requires a DEEP wall box. (35mm recommended). May require a right-angle F adaptor (see page 7). Suitable for carrying all signals 0 - 2015 MHz. Click on each image to enlarge. Buy our Digital Wall Plate and insist that your installer fits it! Read about interference wallplate More info. |
| |
|  | PLATE5F wall plate with 5 'F' connectors. Unlike many wall plates, this has five threaded "F" connectors which go ALL THE WAY THROUGH. You fit an "F" plug on the cable coming through the wall and screw it directly into the rear connector. (Conventional unscreened types use a bridge clamp and a screw which kink the cable AND leave the central core exposed to interference.) A shallow wall box might suffice, provided that the cables come straight through the wall without bends. Otherwise requires a DEEP wall box. (35mm recommended). May require a right-angle F adaptor (see page 7). Suitable for carrying all signals 0 - 2015 MHz. Click on each image to enlarge. Buy our Digital Wall Plate and insist that your installer fits it! Read about interference wallplate More info. |
| |
|  | Suitable for carrying all signals 0 - 2015 MHz. |
| |
|  | |
| | |
|  | Suitable for carrying all signals 0 - 2015 MHz. Ideal for Sky Plus. Off-white. This plate needs two separate cables. |
Diplex Wall Plates (signal decombiners) A Diplex plate has one cable entry carrying two signals. (It may look as if there are two cable entries on the rear but only one of them has electrical contacts fitted.) |
|  | *Non-isolated means that there is no capacitor to prevent a small DC voltage passing through the UHF connection so the socket can be used where a current at up to 24 volts is required to power equipment such as a tvLINK or an aerial masthead amplifier. This is a DECOMBINER plate that has one cable feeding TV (UHF) and radio (FM and/or DAB) into it from a Loft Box or from our UHF/FM diplexer. It separates the two into their own sockets. The TV socket can also feed the remote control signals back to a suitable Loft Box. UHF (TV) output socket requires a female TV (IEC) plug. Radio output socket requires a male TV (IEC) plug. The connections are fully screened to eliminate the possibility of interference. MORE INFO |
| | Choose delivery method |  | |
|  | Televes HB5264 UHF + RADIO non-isolated* wall plate - OBSOLETE Identical specification to the GLO28 above. |
| |
|  | Identical specification to the GLO28 above. MORE INFO |
| |
|  | Identical specification to the GLO28 above. MORE INFO |
Triplex Wall Plates (signal decombiners) A Triplex plate has one cable entry carrying three signals. (It may look as if there are two cable entries on the rear but only one of them has electrical contacts fitted - except in the case of a plate with a RETURN feed, which takes two cables.) |
|  | Labgear PSW132 (or equivalent) Triplexed Decombiner output plate TV / RADIO/Satellite One cable from the diplexer or loft box carries TV, Radio and satellite to the wall plate. There is no return feed. Satellite output socket requires "F" connector. UHF (TV) output socket requires a female TV (IEC) plug. Radio output socket requires a male TV (IEC) plug. MORE INFO |
| |
| |
|  | Triax 304109 Triplexed, (TV / Radio / Satellite /) + Return Decombiner plate One cable from the diplexer or loft box carries TV, Radio and satellite to the wall plate. A second cable from the wall plate carries the return feed back to the distribution system in the loft. Satellite output socket and Return Feed input socket both require "F" connectors. UHF (TV) output socket requires a female TV (IEC) plug. Radio output socket requires a male TV (IEC) plug. MORE INFO |
| |
| Choose delivery method |  | |
|  | Triax 304110 Triplexed, (TV / Radio / Satellite) + Return + Two Telephone Outlets One cable from the diplexer or loft box carries TV, Radio and satellite to the wall plate. One cable from the wall plate carries the return feed back to the distribution system in the loft. Satellite output socket and Return Feed input socket both require "F" connectors. UHF (TV) output socket requires a female TV (IEC) plug. Radio output socket requires a male TV (IEC) plug. There are also two telephone secondary sockets. MORE INFO |
| |
| Choose delivery method |  | |
|  | Triax 304114 Triplexed, [TV (male IEC) / Radio (fem IEC) / Satellite (F)] + Satellit (F) and Return (fem IEC) + One Telephone Outlet. Suitable for SKY+. NOT for use with Triax DDU 333112. One cable from the diplexer or loft box carries TV, Radio and satellite to the wall plate. Signals are separated for the three sockets. One additional cable from the wall plate carries the return feed back to the distribution system in the loft. One separate F connector for an additional LNB cable (or whatever you care to use it for). There is also one telephone secondary socket. MORE INFO |
| |
| |
|  | Televes 5718 Triplexed, [TV (male IEC) / Radio (fem IEC) / Satellite (F)] + Satellit (F) and Return (fem IEC) + One Telephone Outlet. (Identical to above plate but different socket layout). Suitable for SKY+. One cable from the diplexer or loft box carries TV, Radio and satellite to the wall plate. Signals are separated for the three sockets. The return feed back to the distribution Televes "Attic Box" in the loft is combined with the incoming SAT2 LNB cable. There is also one telephone secondary socket. For use with Televes Attic Box only. |
| |
| |
|  | Blank wall plates available: Please SEE PAGE 5 (Electrical) Single width 210-00039 Double width 210-00040 Can be drilled (with care!) and fitted with our H09-3078 threaded "F" barrels (with nuts supplied on request). Plate fits a standard patress box (see below). You should be able to fit at least two "barrels" on a single width plate. Suitable for carrying all signals 0 - 2015 MHz. Requires a DEEP wall box. (35mm recommended). May require a right-angle F adaptor (see page 7). |
| |
| | Choose delivery method |  | Dont miss our Modular wall plates with clip-in socket inserts |
|  | Steel wall boxes available. Please SEE PAGE 5 (Electrical) for wall boxes. |
| |
|  | Plastic wall boxes available. Please SEE PAGE 5 (Electrical) for wall boxes. |
| | |